トップページ › 無線通信営業部ホーム › ニュースリリース一覧 › 新製品情報　Prewell CorporationIF Amp InGaP HBT IF Amplifer PW119

無線通信営業部

ニュースリリース

プレスリリース：2008年9月10日

新製品情報　Prewell Corporation
IF Amp InGaP HBT IF Amplifer PW119

IF Amp PW119_v11.pdf

Prewell Corporation　-　IF Amp InGaP HBT IF Amplifer PW119
Features
  • DC - 500MHz
  • 22 dB Gain at 70MHz
  • +20.5 dBm P1dB
  • +42 dBm Output IP3
  • Single Voltage Supply
  • Lead-free / Green / RoHS compliant SOT-89 Package

Applications
  • IF Amplifier
  • VHF/UHF Transmission
  • Mobile Infrastructure
  • RFID/ Fixed Wireless

Functional Diagram
Functional Diagram


Description

The PW119 is a high performance InGaP HBT MMIC Amplifier and consists of Darlington pair amplifiers with temperature compensation. The amplifier features high linear performance, high reliability as an IF amplifier and provides stable current variation over temperature. The PW119 operates from a single voltage supply and requires only two DC-blocking capacitors, a bias resistor and an inductor for operation. The device is a general purpose IF amplifier that offers high dynamic range in a low cost surface-mountable plastic SOT-89 packages.


Specifications
Specifications

Test Conditions : T=25°C, Supply Voltage=+5V, Rbias=2.4ohm, 50ohm System, OIP3 measured with two tones at an output power of +9dBm/tone separated by 1MHz.


Typical RF Performance for IF Amp Application Circuit
Supply Bias Voltage = 5V, R(bias)= 2.4ohm, Current= 115mA

images


Gain vs. Frequency Input Return Loss Output Return Loss
Gain vs. Frequency Input Return Loss Output Return Loss
Output IP3 vs. Frequency P1dB vs. Frequency NF vs. Frequency
Output IP3 vs. Frequency P1dB vs. Frequency NF vs. Frequency


IF Amp Application Circuit
IF Amp Application Circuit
Recommended Bias Values
Recommended Bias Values

Output power/Gain vs. Input Power @50MHz Output power/Gain vs. Input Power @500MHz Output IP3 vs. Output Power
F1=69.5MHz, F2=70.5MHz
Output power/Gain vs. Input Power @50MHz Output power/Gain vs. Input Power @500MHz Output IP3 vs. Output Power

Output IP3 vs. Output Power
F1=499.5MHz, F2=500.5MHz		 ACPR IS-95A vs. Channel Power
IS-95, 9 Ch.Forward, 30 kHz Meas BW, +/- 885 kHz offset		 ACPR IS-95A vs. Channel Power
IS-95, 9 Ch.Forward, 30 kHz Meas BW, +/- 885 kHz offset
Output IP3 vs. Output Power ACPR IS-95A vs. Channel Power ACPR IS-95A vs. Channel Power
Absolute Maximum Ratings
Absolute Maximum Ratings
Operation of this device above any of these parameters may cause permanent damage.
Lead-free /RoHS Compliant / Green SOT-89 Package Outline

Lead-free /RoHS Compliant / Green SOT-89 Package Outline

images

ESD / MSL Ratings
  • 1. ESD sensitive device. Observe Handling Precautions.
  • 2. ESD Rating : Class 2(Passes at 2000V min.) Human Body Model (HBM), JESD22-A114
  • 3. ESD Rating : Class IV (Passes at 1000V min.) Charged Device Model (CDM), JESD22-C101
  • 4. MSL (Moisture Sensitive Level) Rating : Level 3 at +260°C Convection reflow, J-STD-020


Evaluation Board Layout (4x4)
images


Mounting Instructions
  • 1. Use a large ground pad area with many plated through-holes as shown.
  • 2. We recommend 1 oz copper minimum.
  • 3. Measurement for our data sheet was made on 0.8mm thick FR-4 Board.
  • 4. Add as much copper as possible to inner and outer layers near the part to ensure optimal thermal performance.
  • 5. RF trace width depends on the board material and construction.
  • 6. Add mounting screws near the part to fasten the board to a heatsink.


プリウェル社詳細は http://www.netwell.co.jp/wireless/maker/prewell.html

お問い合わせ

株式会社ネットウエル　無線通信営業部
電話：03-5368-3453
オンラインでのお問い合わせはお問い合わせフォームから

上へ戻る